|
jonyngr
|
 |
« on: September 12, 2008, 23:11:02 » |
|
RESPECTED MEMBERS I HAVE THREE TOGO BOARD HAS FAULTY
ONE IS SHOW BATTERY ID IS BAD ALLTIME SHOW DISCHARGE BATTERY & DONT CLICK
SECOND BOARD IS SHOW ERROR PUSH THE REALESE BUTTON AGAIN
THIRD BOAIRD HAVE ANY SHORT CIRCUIT WHEN I FIT COMPLETE CONNECTION OF BOARD & GIVE POWER SUPLY THE POWE SUPLY IS DROPED TO 0 WITHOUT ON CAMERA OFF POSITION WHEN I REMOVE FLEXIBLE FLAF OF ABOUT MORE THAN 20 PINS WHICH IS INTERCONNECT BETWEEN RELAY BOARD( SMALL BOARD MOUNT WHITH SHUTTER SB PRISM UNIT COMPLETE} & MAIN TOGO BOARD{MAIN BOARD}
CAMERA IS ON
PLEASE HELP I DONT HAVE NIKON D40 CIRCUIT DIAGRAM
THANKS IN ADVANCE
JONY
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #1 on: September 13, 2008, 13:14:31 » |
|
Dear Jony, i dont understand what you say.
First check all fpc connectors and connections are properly insured(TOGO ,relay pcb, sb pcb,etc.), and take care to connect your work place and yourself to earth
But you can check the DC-DC unit possible cause of troubble.
Also if the camera does not work AE CCD damaged.
Any component of the DC-DC can be replaced by yourself in another case the unit must be replaced, remember that :we are technological dependent .
Regards,
Daniel
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #2 on: September 13, 2008, 13:18:03 » |
|
Also , SQ unit can not work good
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #3 on: September 13, 2008, 14:23:08 » |
|
Other, TOGO be sensitive static charge, to beware
|
|
|
|
|
Logged
|
|
|
|
|
tarunpwl
|
|
« Reply #4 on: September 14, 2008, 20:46:32 » |
|
thanks aldagu for helps
i have service manual of d40 but not have scheamatic diagram can you have thease or provide me anywhere
thanks
i have clearly specify i have three seperate cameras
in one d40 camera show every time battery information is low & not realease click button
probelam is only togo board i confirm this probelam by replace another togo pcb camera is work fine
second d40 camera is trouble is when i on camera lcd show " push the shutter realease button again " this probelam is also in togo board not in sb unit when i replace other togo board camera is working fine
finaly third camera have any short circuit in his togo board when i complete fit that camera all the flexible pcb connect means complete asemble
camear is power off mode i give 7.4v power by external power suply the power suply voltes is dropped to 0 it means short circuit in camera & short circuit in togo board when i replace other togo board camera work fine
in this faulty togo board have short circuit but when i disconnect the connection fpc {1020} between relay board & togo board short circuit is removed & not droped power voltes in both position camera power off & power on
also camera on lcd glow light
thanks verymuch for your information
i need scheamatic is essential
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #5 on: September 15, 2008, 00:40:44 » |
|
Dear jony now yes understanding.
Nikon provides no more information than they are in the service manual.
As things are going to have to replace togo pcb.In first case maybe corrupted the data stored in eeprom or bad zener diode; in the latter case you can drop another relay pcb and see if the short continuous, and check the components relay pcb.Also must verify the pins of the female connector harness, connector may have a bent.
If not identify any component damaged anyway you should change togo pcb.
|
|
|
|
|
Logged
|
|
|
|
|
kiran
|
|
« Reply #6 on: October 12, 2008, 23:20:40 » |
|
hello
d40 camera problem with picture not procees good , after take picture process colour colour like graphic card dame in computer , i have change ccd but same problem , can any one tell me this is problem with main mother board or dc to dc converter ?
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #7 on: October 14, 2008, 10:05:10 » |
|
Hi kiran,
You may have problems with memory compression circuit in TOGO PCB.
You may also have defective component in relay pcb
|
|
|
|
|
Logged
|
|
|
|
|
kiran
|
|
« Reply #8 on: October 16, 2008, 00:36:48 » |
|
Thank you for your kind replay ,
I replaced good main PCB picture quality is good.
I tried repair old PCB by reheat two RAM IC’S no use. Can u please tell me if I change graphic ram IC’s problem can rectify ? I have dead board , if u know any idea regarding this problem please post , I’ll try & tell u result.
And one more request ,can I get new boards in India ? , please give me reseller details.
Regards
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
|
« Reply #9 on: October 16, 2008, 17:50:13 » |
|
Hi kiran, I only know in India www.omaxphoto.com (http://www.omaxphoto.com) contact Mr. Chadha in New Delhi other are in USA ,you can contact Mr. Roman Pastor camerasyes@aol.com supllies a lot of brands.You need send the part Nº you need.
The problem are sure before the RAM Ic's, try to locate.
Best way is to replace TOGO PCB
Regards!
|
|
|
|
|
Logged
|
|
|
|
|
kiran
|
hi
can i get full service manual ? if u have please help me sir
|
|
|
|
|
Logged
|
|
|
|
|
aldagu
|
Hi kiran i have only what was upload to sharefx , for know how work a digital camera loock D1 service manual upload to pardeep days before.
regards!
|
|
|
|
|
Logged
|
|
|
|
|
